2-stamper pic thread

BigWaylon

BigWaylon

Head philatelist
Staff member
2A Bourbon Hound 2024
2A Bourbon Hound OG
Charter Life Member
Benefactor
Supporting Member
Multi-Factor Enabled
Joined
Dec 18, 2016
Messages
64,633
Location
Charlotte
Rating - 100%
71   0   0
Mentioned this in another thread, and thought I might as well start it. Post ‘em up if you don’t mind. I’ll start with my bump-in-the-night HD weapon. Suppressed 7” 9mm AR. It’s an Aero Pew Pew lower I built out with a Hahn mag block adapter and a complete upper (with 9mm YHM upper) from JSE. Octane 9 and Vortex Spitfire.

F8027D8F-5D7F-41F7-BBE4-C9D369D9E090.jpeg
B3730538-8C92-46EE-90F1-45EF7741498B.jpeg

32+1 rounds of HST in it, and 32 more to grab at the same time.

ETA: many a shooter has been introduced to silencers by that setup and a mag loaded with alternating subs & supers…@Dale Gribble was the most recent (last week) 😎
 
CZ Scorpion SBR with a Griffin Rev 9 supressor, Holosun 510c-GR, and a Streamlight Pro Tac. Folding stock, right side AK style safety, both an extended and ambi charging handle, and the Shooters Element spring and trigger job to finish her out. She aint picky at all and eats whatever trash ammo youve got, but I feed her right for the HD role. Just like Waylon's, she's also currently loaded up with 32+1 HSTs and another 32 close at hand.


My sweetheart

20221207_145833.jpg

My sweetheart doing yoga

20221207_145856.jpg

From the top

20221207_145943.jpg
 
Last edited:
Nobody else wants to play?

Here’s another. PS90 with Turbo K (direct thread) and Lil P.

3FE1EDA5-42F0-46A2-B9E3-CF21A8A91E15.jpeg

Usually has 50+1 rounds of FN 40gr blue-tipped V-Max, but I haven’t reloaded that mag after a range trip or two.
 
Here's the "Many Gadgets" project. It's a SBRed poverty pony lower with a no-name 8" 5.56 barrel, Pantheon QD, Sylvan folder, spitfire 1x prism and a Saker 7.62 muffler. It all fits in a pretty small Starlight case.

20221208_100112.jpg

20221208_100126.jpg

20221208_100226.jpg
 
ytynZMyh.jpg
 
I can't stress how much I like this gund how accurate and reliable its been. It runs on subs , it runs on supers. Is it my favorite gun? I dont like to lay that much pressure on her but its certainly my go to gun.

300 BO Rattler upper kit on a SIG M400 lower, Sig fixed folder and Elcan 4X . SIG SRD762Ti can.


PXL_20220930_132346024.jpg
 
My only current two stamper. Shoots great with 150 syntech. However I really like the CGS on my MR920 and Beretta, so I may eventually seek a more dedicated (and slightly shorter) pcc can for this setup and leave the CGS for my handguns. It’s annoying to switch out between the three lug and piston

4150BA92-2645-4225-BA61-12F3BCFC74D6.jpeg
 
PisgahPlinker said:
My only current two stamper. Shoots great with 150 syntech. However I really like the CGS on my MR920 and Beretta, so I may eventually seek a more dedicated (and slightly shorter) pcc can for this setup and leave the CGS for my handguns. It’s annoying to switch out between the three lug and piston

View attachment 557465
Click to expand...
That needs a MG7K 358 dedicated to it. 😎
 
This one has made many a grown man giggle…

S&W M&P 15-22, with the barrel cut down to 4.5”. Form 1 can fills the rail up nicely, and recently swapped to a 1.5X prism. Silencer is 1.25x6.5. Pretty much keeps bulk pack ammo subsonic, unlike my 15-22 pistol.

1A5D444F-9EF4-4290-8041-FEFB760975BC.jpeg
DC084313-5445-4D50-96F3-5311764C713F.jpeg
CCAA3FB7-C527-40A8-924C-BCF5192DF757.jpeg

Best thing about it? I engraved the NFA info freehand with a Dremel. Function over form, all day long. 🤣😎

C565F21D-8883-47AB-AF86-7191E7421F3F.jpeg

If you happen to notice any of the pink spots, that’s just some wear and tear. I bought a used factory rail to cut down when I built that F1 can, and the first one I found was the pink & black muddy girl camo…so I just sprayed it black.
 
TrappyBoy said:
How do you like that DBAL-D2? I hear they’re just as powerful as the laser based A2 just with a cleaner beam and more weight.
Click to expand...
I love it. It is much brighter than the A2. About the same as a FP Peq15. You are right about the weight though - she's chonky. I just listed an excellent starter PVS-14 in the classifieds if you're interested!

NC - Excellent Starter PVS-14 - $2500

Elbit XLSH GP PVS-14. Purchased new from Night Vision Guys October of 2021 (Warranty through 10/23). Less than a full battery's worth of use. Image quality is excellent - better than many WP tubes I've looked through. Zero blems. High Photocathode Sensitivity/SNR and low EBI/Halo all contribute...
carolinafirearmsforum.com carolinafirearmsforum.com
 
Last edited:
DSG/Seekins upper rebarreled with 8” BA & wearing a Sandman-K. Poverty pony lower & cheap Vortex RDS. Overall barrel length with the can is a tick over 13.5”. Remodeled ‘er a couple years ago, put off shooting & dialing it in, then moved cross country. 😐 Now that I can shoot in my yard, need to get it tuned for suppressed subs.
720767AF-D300-469D-BFA4-B3400CF7E4FE.jpeg
 
If I was ever going to hunt, I believe this would be the rifle. PSA lower and MOE LBK. Upper started as a Bison 16” 6.8 BSP that I had them Cerakote the barrel ODG before shipping it. Ended up sending it off to ADCO for them to cut it down to ~12”. I wasn’t particular on the length measurement, but I wanted it cut so the flash hider holes were just outside the handguard. This resulted in the can (YHM ULT) just barely being tucked inside. You might be able to tell the barrel is green in the 4th pic. Bison was also kind enough to share their gas port size on their 11.5” BSP, so ADCO opened mine up to match since it was close to the same length.

84A156F4-B34C-4A80-A11D-F16E0697E57F.jpeg
62B76C1B-BD2A-4BCB-A810-DB8A6692C77A.jpeg
6C95C294-E811-4D24-B163-A586819A63D3.jpeg
7B238BE6-63DC-4C78-A47B-0FC9C36AA5DE.jpeg

Stenciled and striped some PSA/D&H 6.8 mags:

786E2CCF-F41E-4F4A-AE66-0D39427F9479.jpeg

And in the case of so exactly what the law says, no matter how stupid, I had to engrave caliber. This is the only SBR I have where I had to do that. But the lower says multi, and I lost the barrel markings when it was cut down. So, I took a Dremel and engraved 6.8mm between the pivot pin ears. Nobody will ever see it, but it’s perfectly legal/visible.

FCBEDFAD-5421-49A9-9FAC-A728E4510A1B.jpeg
 
Crazy Carl said:
DSG/Seekins upper rebarreled with 8” BA & wearing a Sandman-K. Poverty pony lower & cheap Vortex RDS. Overall barrel length with the can is a tick over 13.5”. Remodeled ‘er a couple years ago, put off shooting & dialing it in, then moved cross country. 😐 Now that I can shoot in my yard, need to get it tuned for suppressed subs.
View attachment 559482
Click to expand...
Sandman is keymo only correct? How are you ratcheting down under the handguard? Or just install suppressor and then slip hand guard over the entire assembly?
 
PisgahPlinker said:
Sandman is keymo only correct? How are you ratcheting down under the handguard? Or just install suppressor and then slip hand guard over the entire assembly?
Click to expand...
You don’t have to touch that “ring” to install or remove Keymo.
 
I wondered if that was it. My MP5 SD is a sear gun with the sear number also stamped on the receiver. I was told that even if the sear wasn't present since the receiver was engraved I was legal and did not need an SBR stamp.

That was 30+ years ago though, and I'm sure that ATF has changed their interpretation a few times since then.
 
Scsmith42 said:
I wondered if that was it. My MP5 SD is a sear gun with the sear number also stamped on the receiver. I was told that even if the sear wasn't present since the receiver was engraved I was legal and did not need an SBR stamp.

That was 30+ years ago though, and I'm sure that ATF has changed their interpretation a few times since then.
Click to expand...


Yeah, They want the sear essentially married to the gun now. You couldn't use it in another gun without SBR'ing the one the sear is in now,
 
Well it appears to me that all the stuff pictured in this thread seem to be SBR + Suppressor.
My 3 stamps are: machine gun (trigger pack) + suppressor + SBR. The host gun pictured wasn't purchased as a machine gun, I had the pack long before I bought and SBR'ed that rifle.
 
You must log in or register to reply here.
Back
Top Bottom