Well I bought one last night, so I think we should!
Ordered online, hopefully it'll be here by Friday.I can't see the pic.
Outstanding!Got this in today. Thing I'm most happy about that I didn't realize is this doesn't use a full length backer so I should be able to mount it a little farther forward whereas I couldn't do that with my rail section because of the gas block.
What upper are you going with?
What upper are you going with?
Larue Tactical had an early adopter sale on the SUURG upper kit- 20% off, and I had Larue gift cards...
Nice! They introduced the SUURG right after I ordered my UU Grendel. I'm not mad about it, I'm actually happy as it made the decision easier lol.
I'm at 2 weeks on my upper, so hoping to be seeing something soon, as I am anxious to get it!
What lower are you going with? Is that still a 15 platform or is it 10?
Is that the STS Ambi? That's a damn good looking piece of kit.And it starts again.
Yea, got it today.
Yea, got it today.
Just go ahead and post yours
Gorgeous!NICE! They also have the M4E1 upper and lower for $150.
Also, I'M IN LOVE...
View attachment 35784 View attachment 35786 View attachment 35787 View attachment 35789
Yes it's Aero's burnt bronze. I know because its the set I sold him!What color is that pistol coated? Is that the burnt bronze?
They both look good!
I have it's little brother(kinda)!Paint didnt come out as I had wished. It's a lot lighter than described. But not terrible.
View attachment 37185
It's close!I have it's little brother(kinda)!
Got some new FN barrels in. Difference between Crane's cut down 10.3" Govt profile and FN's new 10.3" SOCOM bbls. Gas port is a measured .070"
The parts: FN bbl, upper, BC and bolt, DD RIS II Mk18, PRI CH, SF4P FH and KAC front sight. Rest of parts are all govt contracted. Only thing that's used was the Forward Assist, almost selected a teardrop M16.
Assembled and installed on select fire lower w/SSF trigger. Second we built this week with FN bbl. Bit heavier up front of course. Wish I could build these at home, but as is its DoD property downrange.
CD
Are these custom built to an individuals requests/needs or are they ordered by a specific unit? I have allways wondered how much input individuals have on rifle setup. I hope I am not overstepping by asking and 100% understand if you can't answer.Got some new FN barrels in. Difference between Crane's cut down 10.3" Govt profile and FN's new 10.3" SOCOM bbls. Gas port is a measured .070"
The parts: FN bbl, upper, BC and bolt, DD RIS II Mk18, PRI CH, SF4P FH and KAC front sight. Rest of parts are all govt contracted. Only thing that's used was the Forward Assist, almost selected a teardrop M16.
Assembled and installed on select fire lower w/SSF trigger. Second we built this week with FN bbl. Bit heavier up front of course. Wish I could build these at home, but as is its DoD property downrange.
CD
Can you recommend a 10" 300BLK barrel for pistol length gas? Primary concern is accuracy.These barrels are USSOCOM specs. NSW Crane cuts down 14.5" bbls to 10.3" and opens up the gas port to .070. Barrels are then dimpled for a low profile gas block and rethreaded to 1/2x28. The FN barrels are the SOCOM heavy bbls to the same specs. These barrels are used on 10.3" URG/Mk18 guns. Don't have a scale to weigh the barrels unfortunately and we do have the proper SF SOCOM suppressors.
CD
Can you recommend a 10" 300BLK barrel for pistol length gas? Primary concern is accuracy.
I like that!I ended getting this.. it was too good of a deal to pass up. I haven’t shot it or even decided what scope it needs..
RRA LAR-8 .308
View attachment 37274