Exspiravit
Mell-Known Wember
2A Bourbon Hound 2024
Benefactor
Life Member
Supporting Member
Multi-Factor Enabled
Oh, that sucks.It's a 22lr barrel and works with the special bolt.
Oh, that sucks.It's a 22lr barrel and works with the special bolt.
I've got to get the nut off to change the handguard outLeave the barrel black? Just use a paper towel roll to mask the barrel inside the hand guard.
Bear Creek Arsenal, and yes I know, I know. But CMMG is insanely expensive and nobody else seemed to make one anymore.Forgive me if I missed it up stream. What exact make and model is the upper?
No judgement zone. I was just going to poke around and look at a disassembly video if I could find one,Bear Creek Arsenal, and yes I know, I know. But CMMG is insanely expensive and nobody else seemed to make one anymore.
I suspect it was cranked on with a six foot bar by a gorilla. I'm trying to decide if I can cut the nut without buggering the upper.No judgement zone. I was just going to poke around and look at a disassembly video if I could find one,
I really hope not.Is this a British thing!? Jus sayin…
If you don’t use a feather boa as a sling I will lose all respect for you.
Maybe I can do some lettering with tiny bedazzles......
So ...... What's happeningemailed BCA again to see if they can help.
I've been forgetting to print the label. Boxed it, labeled it and it's ready to go tomorrow.So ...... What's happening
Why take the fun out of it now?.Now to find somewhere to paint the thing without poisoning myself!
I've got to get the nut off
if I can cut the nut without buggering
once I degrease and dry
I don't even have drawers, I use plastic totes.I always keep my extra AR parts in my sock drawer. If I put them in my reloading room after a day or two I can’t find them. Too much other stuff in there. I keep my Garand parts in my underwear drawer. You have to have a system.
I had a dresser, wasn't for me.Then you mislay the tote and spend 2 days looking for it, my bedroom dresser ain't going nowhere.
Two laundry baskets. One for clean, one for dirty. All you really needI had a dresser, wasn't for me.
Commando painting project, then.I don't even have drawers
You can borrow these if you need?Also is there an alternative to the bloody bolt release roll pin? I've never not dinged the receiver getting that bastard in. I know KNS used to make one with a tiny c clip but is there something that maybe screws together?
I have those as well if you need/want.You can borrow these if you need?
Wheeler Delta Series AR-15 Bolt Catch Installation Punch Kit
The Wheeler Engineering AR-15 Punch Kit includes everything you'll need for installing the bolt catch pin. The kit includes a starter punch and a...www.midwayusa.com
It's like watching the development of the SA80 in real time.So much build up, no delivery. Brits, amiright?
Put masking tape on the receiver. Take a small flat file and taper the roll pin on one end just a tad, makes it easier to start, and you’ll never see it once it’s in, put a dab of oil on the hole, cause every hole needs lube.Also is there an alternative to the bloody bolt release roll pin? I've never not dinged the receiver getting that bastard in. I know KNS used to make one with a tiny c clip but is there something that maybe screws together?
I use Knipex pliers, as they pinch parallel. Just a wrap of tape, pinch, pinch, pinch and it’s done. No marring or scratches.Also is there an alternative to the bloody bolt release roll pin? I've never not dinged the receiver getting that bastard in. I know KNS used to make one with a tiny c clip but is there something that maybe screws together?
You can borrow these if you need?
Wheeler Delta Series AR-15 Bolt Catch Installation Punch Kit
The Wheeler Engineering AR-15 Punch Kit includes everything you'll need for installing the bolt catch pin. The kit includes a starter punch and a...www.midwayusa.com
Thanks! I've been using channel locks and electrical tape lolI have those as well if you need/want.
You sound like my ex wife lolSo much build up, no delivery. Brits, amiright?
They pinch on an angle and will scratch it every time in my experience.Thanks! I've been using channel locks lol
Hardly. I haven't even got into the meth yet.It's like watching the development of the SA80 in real time.